Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Installation Cost in Enterprise?
Gate installation in Enterprise typically costs $1,800 to $4,200 for a manual driveway gate and $3,500 to $8,500 for an automated gate, including the operator, safety sensors, and access controls. A single-pedestrian walk gate runs $900 to $2,200. Those numbers are estimates for the Las Vegas Valley market in 2026; the final price is set by a written on-site estimate after we look at your driveway, soil, and power situation.
Enterprise sits on desert ground where caliche and packed gravel change how fence and gate posts get set, and that single variable can shift a gate quote by hundreds of dollars. We’re gate specialists, not a general handyman service, and we install and repair gates across nine major brands so we can quote your actual system instead of guessing at it.
Key Takeaways
- Manual driveway gate installation in Enterprise: roughly $1,800 to $4,200.
- Automated gate installation in Enterprise: roughly $3,500 to $8,500, operator and access control included.
- Walk gates: roughly $900 to $2,200 depending on width and material.
- Equipment replacement (operator upgrade on an existing gate): roughly $1,200 to $3,000.
- Caliche, slope, and power routing are the three biggest swing factors in Enterprise.
- Estimates are free. Call (844) 423-3067. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Gate Installation Cost Breakdown (2026)
Below is how gate installation pricing breaks down in the Enterprise market. Each line is a range, not a fixed quote, because the final number depends on your specific gate, the operator brand, and site conditions. The written estimate is what sets the price.
| Line Item | Typical Range (Enterprise, NV) |
|---|---|
| Walk gate (single pedestrian, 3-5 ft) | $900 – $2,200 |
| Manual driveway gate (single swing, up to 12 ft) | $1,800 – $3,200 |
| Manual driveway gate (double swing or sliding) | $2,500 – $4,200 |
| Automated single swing gate (with operator) | $3,500 – $6,000 |
| Automated double swing or sliding gate | $4,800 – $8,500 |
| Operator replacement on existing gate | $1,200 – $3,000 |
| Access control (keypad, remote, or entry system) | $350 – $1,400 |
| Safety sensors and photo-eye setup | $200 – $600 |
| Concrete footings and caliche excavation | $300 – $1,200 |
| Electrical service run to gate location | $500 – $2,000 |
| Gate removal and haul-away of old unit | $150 – $500 |
What pushes a job toward the top of these ranges: a heavy steel or wrought-iron gate, a long driveway run for power, a brand operator with entry-system integration, or a site where caliche has to be broken out before footings go in. What keeps a job near the bottom: an aluminum gate on a short, flat, already-wired driveway using a standard operator like a LiftMaster or Linear unit. Most Enterprise homeowners land somewhere in the middle.
We work on the nine brands that cover the vast majority of residential and commercial gates in this market: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. If your existing gate already runs one of those operators and you’re replacing the gate but keeping the operator, the quote drops because the automation side is already done. If you’re starting from scratch, we quote the gate, operator, access control, and wiring as one job so you’re not hunting down a separate installer for each piece. That’s the advantage of a specialist: repair and installation under one roof.
What Affects Gate Installation Pricing in Enterprise
Two gates of the same size can quote hundreds of dollars apart in Enterprise. Here’s what drives the difference.
- Caliche and soil conditions. Enterprise ground often has a layer of caliche just below the surface that has to be broken out before a post can be set. That excavation and extra concrete is a real line item, not a rounding error.
- Driveway slope and grade. A gate on flat ground uses a standard operator. A gate on a slope needs an operator sized for the grade, sometimes a different arm or a sliding design, and that changes the price.
- Power availability at the gate location. If there’s no electrical service near the gate, routing it is one of the larger line items on the job. Solar-capable operators like Ghost Controls and Mighty Mule can eliminate that run when the site allows it.
- Gate material and weight. Aluminum is the lightest and cheapest to automate. Steel and wrought iron are heavier, need stronger hinges and a larger operator, and cost more across the board.
- Operator brand and access control. A basic remote-only setup is the low end. Adding a DoorKing entry system, keypad, or intercom moves it up. Each brand has its own quirks, and matching the right operator to the gate is part of what we quote.
- Permits and HOA requirements. Some Enterprise neighborhoods and HOAs have rules about gate height, setback, and style. Check with your city’s building department and your HOA before the install, since those requirements can add design work or limit what you can build.
How to Save on Gate Installation
You don’t have to accept the first number you’re quoted. Here’s how Enterprise homeowners keep gate installation costs down without cutting corners on safety.
- Keep the existing operator if it’s in good shape. If your gate is worn out but the operator still works, replacing only the gate can save a large part of the automated quote. We’ll tell you honestly whether the operator has enough life left to make that worth doing.
- Choose solar-capable operators when power is far away. A Ghost Controls or Mighty Mule solar setup can avoid a long electrical run, which is often one of the biggest single costs on a rural or long-driveway install.
- Match the gate material to the job. If you don’t need wrought iron, aluminum does the same job for less, and it’s easier on the operator.
- Get the estimate in writing before any work starts. A written estimate locks in the line items so you’re not surprised by footing or wiring costs later. Our estimates are free, and the written estimate sets the final price.
- Bundle repair and install if your old gate is failing. If a technician is already out assessing a repair and the gate is past saving, rolling that assessment into an install quote saves a second visit.
We answer 24/7, so if a gate fails and you’re weighing repair against replacement, call and we’ll book an on-site estimate. Call (844) 423-3067 for a free estimate.
Should You Repair or Replace Your Gate?
Repair is usually the cheaper call when the gate structure is sound and only the operator, control board, or access system has failed. Replacement makes more sense when the gate itself is rusted through, sagging off its hinges, or so far out of alignment that the operator can’t hold it.
A common scenario in Enterprise: the gate is fine, but the operator has stopped responding or the control board has failed. That’s a repair, often well under what a full install costs, and it’s exactly the kind of electric gate problem we diagnose at the source. We work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule operators, so the odds are good we know your system. If a repair assessment turns into a replacement, you don’t have to source a separate installer afterward. That’s the single point of contact from diagnosis through repair or full installation.
For more on the repair side, see the full Gate Repair Enterprise service overview, and if you’re local to the area, the Enterprise page covers the market in more depth.
What’s Included in a Gate Installation Quote
A complete gate installation quote in Enterprise should cover four things: the gate and its hardware, the operator and access control if it’s automated, the site work (footings, excavation, wiring), and removal of the old unit if there is one. If any of those are missing from a quote, ask why. A number that looks low often leaves out the wiring or the footings, and those show up as add-ons later.
We quote gate, operator, access control, and site work as one job so the number you see is the number you’re working with. If a brand-specific part like a control board or a receiver needs to be ordered, that’s part of the estimate, not a surprise. Since we’re a gate-only specialist, every part and every technician skill is dedicated to gates, which means fewer surprises about what’s covered.
Electric Gate Installation: What’s Different
An electric gate install costs more than a manual one because it adds three things: an operator, a power source, and access control. The operator is the biggest single line item, and the brand you choose matters. A LiftMaster or Linear operator is common on residential driveways. A DoorKing entry system is more typical on a property manager’s commercial or multi-unit gate. FAAC, BFT, Viking, and Elite cover different operator types and gate weights.
Access control is where a lot of homeowners underspend and then regret it. A keypad and remote setup is the baseline. If you need to grant access to multiple people, a call box or entry system pays for itself in not having to hand out remotes. We diagnose and repair electric gate operators, control boards, and access systems, not just the mechanical side, so an install includes the automation done right the first time.
Safety and Permits for Gate Installation in Enterprise
Automatic gates involve moving parts, electrical wiring, and access control, and those carry real safety responsibilities. An automatic gate operator needs functioning safety sensors so the gate stops if something is in its path, and the electrical connection has to be done properly. This is not a DIY wiring job. We handle the operator wiring and safety setup as part of the install and flag anything that isn’t right before the gate goes into service.
Permit rules vary by jurisdiction. Most cities require a permit for a new gate and fencing, and some Enterprise HOAs have their own requirements about height and style, so check with your city’s building department and your HOA before the install. If you’re a property manager, document the access-control setup for your records, since keypad and entry-system credentials matter for building security. We’ll walk through what the install involves so you know what to expect, without claiming any specific code requirement that isn’t yours to meet.
Why Choose a Gate Specialist for Installation
A gate is not a fence panel and not a garage door. It’s a hinged or sliding structure with hinges, latches, alignment, and often an operator and access system, and it has to hold up under daily use. A generalist who installs gates as a side service can get a manual gate hung correctly, but the automation is where the specialization pays off.
We’re a gate-only specialist with technicians who have up to 8 years of experience, fluent in the quirks of each of the nine operators we support. When you call about installation, the person who answers knows what a LiftMaster arm does differently from a Mighty Mule, and can tell you which one fits your gate. That’s the difference between a working install and one you’re calling someone back about. We’re not a garage-door company that dabbles in gates, and we’re not a general contractor with a gate crew. Gates are the whole job.
FAQs – Gate Installation Cost
How much does gate installation cost in Enterprise, NV?
A manual driveway gate installs for roughly $1,800 to $4,200 in Enterprise, and an automated gate runs about $3,500 to $8,500 including the operator and access control. Walk gates are around $900 to $2,200. Call (844) 423-3067 for an exact quote; estimates are free.
Is it cheaper to repair or replace a gate?
Repair is cheaper when the gate structure is sound and only the operator or control board has failed, often well under the cost of a full install. Replacement makes more sense when the gate is rusted, sagging, or badly out of alignment. We can tell you which side of that line your gate is on during a free estimate. Call (844) 423-3067 to book an on-site assessment.
Can you install an automatic gate the same day?
A full automated install usually isn’t same-day because site work, wiring, and operator setup take time. A repair on an existing automated gate can often be handled same-day. We answer 24/7 and dispatch Sunday through Friday, 7am to 7pm. Call (844) 423-3067 to get on the schedule.
What brands do you install and repair?
We install and repair gates and operators from LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Those nine cover the bulk of residential and commercial gates in the Enterprise market. Call (844) 423-3067 to confirm your brand before booking.
Do I need a permit for a gate in Enterprise?
Permit requirements vary, and most cities require one for a new gate or fence, so check with the city’s building department and your HOA before the install. We’ll tell you what the install involves so you can ask the right questions. Call (844) 423-3067 with your address and we’ll walk through it.
Get a Free Gate Installation Estimate in Enterprise
A gate install in Enterprise is a real investment, and you deserve a number that holds up. We install and repair gates across nine major brands, with technicians who have up to 8 years of experience and a gate-only focus. From a stuck gate to a full installation, you get one point of contact from diagnosis through the final job. If your brand needs service, we work on your brand. If your gate is failing and you’re not sure whether it’s a fix or a replacement, we’ll tell you straight.
Call (844) 423-3067 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. The written estimate sets the final price, and the price is set per job after we’ve looked at the gate, the site, and the operator.
Pricing reflects the Enterprise market as of 2026. Gate Repair Enterprise offers free estimates – call (844) 423-3067.
Written by the team at Gate Repair Enterprise.
What Our Customers Say
"Fixed the immediate problem. He was honest that the operator is near end of life and I should budget for a replacement, which I appreciate even if it wasn't what I wanted to hear."
- Travis Kowalski"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
- Alejandro Rodriguez"Photo eye was misaligned so the gate refused to close after dark. Ten minute fix. He also cleaned the lens and pointed out that the sprinkler head was spraying it every morning, which is why it kept happening."
- Hector Hernandez