Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Motor & Opener Cost in Enterprise?
Replacing a gate motor and opener in Enterprise typically costs between $450 and $1,800 for a residential swing gate, and $600 to $2,400 or more for a sliding gate operator, with the written estimate setting the final price. A straightforward swap of a failed opener on an existing residential gate often lands in the $500 to $900 range, while commercial slide gate operators and full access-control systems climb higher. We work on the brand you already have, which usually keeps the job at a repair or a like-for-like replacement instead of a full changeover.
Every estimate we give is free and priced per job. Our technicians have up to 8 years of experience, and we’re gate specialists, not generalists – every part and every skill on our side of the call is dedicated to gates. Call (844) 423-3067 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Key Takeaways
- Residential gate motor and opener replacement in Enterprise runs roughly $450 to $1,800 for swing gates and $600 to $2,400 for slide gates.
- Operator brand and gate type drive most of the price – a LiftMaster or Linear swap costs less than a DoorKing commercial replacement.
- Replacing just the motor or just the control board is usually cheaper than a full operator changeout.
- Estimates are free, and the price is set per job by the written estimate.
Gate Motor & Opener Cost Breakdown (2026)
We price gate motor and opener work line by line so you can see exactly where the money goes. The table below shows typical estimated ranges for the Enterprise market in 2026. These are ranges, not exact figures – your written estimate sets the final number once we’ve looked at your gate, your operator, and your power and access setup. Gate Repair Enterprise handles the whole job from diagnosis through repair or full installation under one roof, so you’re not sourcing a separate installer after a repair assessment.
| Line Item | Typical Estimated Range (Enterprise, 2026) |
|---|---|
| Diagnostic visit and written estimate | Free |
| Residential swing gate opener replacement (motor and arm) | $450 – $1,200 |
| Residential slide gate operator replacement | $600 – $1,600 |
| Control board replacement | $180 – $450 |
| Receiver and remote/keypad replacement | $120 – $350 |
| Safety sensor / photo-eye replacement (pair) | $150 – $400 |
| Battery backup install | $200 – $450 |
| Motor-only or gearbox-only rebuild | $250 – $650 |
| Wiring repair to operator and power | $200 – $600 |
| Commercial slide gate operator replacement | $1,200 – $2,400+ |
| Full gate + new operator installation | $2,500 – $8,000+ |
| Brand-based tune-up and re-sequence | $120 – $250 |
What pushes a gate motor job toward the top of a range is usually the operator type and the access system behind it. A residential swing-arm opener on a single-leaf driveway gate is the least expensive class of work. A commercial slide gate operator with a loop detector, keypad, intercom chip and a separate control board is at the other end. A gate that needs new wiring because the run to the operator has failed usually lands higher than a straight motor swap, because we’re pulling wire, not just bolting on parts.
When we diagnose electric gate problems at the source, we can tell you whether the motor, the control board, the access system or the gate itself is the failing component. That matters for price. A failed receiver on a LiftMaster or Linear operator is a fraction of a full operator replacement. A seized gearbox on a Mighty Mule can often be rebuilt instead of replaced. Our goal is the right fix for your specific system, not the biggest job.
What Affects Gate Motor & Opener Pricing in Enterprise
Six things move a gate motor quote up or down in Enterprise. Most of them come down to the system you already have, not the neighborhood you’re in.
- Operator brand and model. We work on nine major gate and operator brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. A replacement motor on a common residential operator brand usually costs less to source than a commercial-class DoorKing or FAAC unit. Brand-matched parts and known troubleshooting patterns keep the labor tighter.
- Gate type – swing vs. slide. Slide gate operators carry a higher parts cost than swing operators, and they need more attention to track, rollers and the foundation of the gate itself. A swinging gate that’s settled or dragging adds work before the operator goes on.
- Access system complexity. A single remote and one receiver is a simple job. Keypads, telephone entry systems, intercom wiring and loop detectors add to the parts list and to the diagnosis time. We handle the wiring for these as part of the operator job rather than handing it off.
- Power and wiring run. The distance from the power source to the operator, and the condition of the run, affects labor. Old or spliced low-voltage wire and a failed transformer both get replaced as part of the job.
- Gate condition. A gate that’s leaning, binding, or off its track needs mechanical work before a new motor will last. We won’t sell you a motor to fight a bad gate. If the frame needs repair before an operator install, that’s priced in honestly up front.
- Commercial vs. residential duty. Commercial gates run more cycles per day and need heavier-duty operators. A commercial slide operator replacement is priced well above a residential job because the operator itself is built for higher duty.
Enterprise’s desert location does influence the work. Gate operators sit in summer heat for months at a time, and the electronics – control boards, receivers, battery backups – are the parts that feel it most. Dust off the driveway and street settles into slide tracks and rollers, which puts more strain on the motor and gearbox over time. Keeping the track clear and rollers true is cheaper than replacing an operator a season early.
How to Save on Gate Motor & Opener
The best savings on a gate motor job come from fixing the smaller parts before they take the operator down with them, and from knowing when a repair still makes sense.
- Get the diagnosis first. A free estimate tells you whether you need a full operator replacement, a control board, or a receiver swap. A technician won’t guess at a motor when the actual failure is in the access system.
- Repair before you replace. A motor, gearbox, control board, or receiver can often be replaced on its own. Replacing the whole operator when one component has failed is the most expensive way to solve a small problem.
- Keep the track and rollers clear. In Enterprise, dust and grit settle into slide tracks. Sweeping the track and checking rollers is a routine habit, not a paid service, and it takes load off the motor.
- Match your brand. Because we work on the brand you already have, we can often source the exact replacement part instead of switching brands and re-fitting the whole access setup.
- Bundle installation and repair. If your gate needs structural work and a new operator at the same time, pricing them together is cheaper than two separate visits.
None of these savings change the safety rules. Gate operators carry mains voltage at the control box, and the heavy gate leaf can crush. We don’t recommend homeowner wiring work on the operator or the power side – that’s a job for a trained technician. Call (844) 423-3067 for a free estimate on your gate motor or opener. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
When a Repair Makes More Sense Than a Replacement
Replacing just the failed component is often the smarter call, and a free estimate will tell you which way to go. For a working operator with a dead control board, a failed receiver, a worn gearbox or a bad battery backup, the repair is cheaper by a wide margin – usually $180 to $650 depending on the part. For operators that have failed the motor itself, burned out the control board and are past their mechanical life, replacement is usually the better spend. We diagnose electric gate problems at the source so the recommendation fits the actual failure. If a repair will hold, we’ll tell you. If a replacement is the cleaner path, we price the full job.
What Happens When You Call
You call (844) 423-3067 and tell us your gate type, your operator brand and what it’s doing – not opening, opening partway, cycling on its own, arm not retracting, or remote not working. We book a visit, and a technician arrives to look at the gate and the operator, checks the control board and access wiring, and writes up a free estimate. From a stuck gate to a full installation, that’s the whole job under one roof, with a single point of contact from diagnosis through repair or full installation.
Because we only work on gates, every part and every skill on the job is gate-related. We’re not spreading across unrelated trades. We work on your brand – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule – so a familiar operator isn’t a guessing game. For a wider look at how we handle gates in this city, see our Gate Repair Enterprise page.
Why Brand Matters on a Gate Motor Job
Gate operators aren’t interchangeable, and brand-matched expertise changes both the price and the outcome. A technician who knows the wiring quirks of a LiftMaster swing-arm opener, the control-board fault codes on a DoorKing slide operator, or the gate travel limits on a FAAC system will usually find the fault faster and avoid guesswork parts. That keeps labor down. Some failing brands can be repaired on the spot; others are best replaced with a same-family unit so the access system, remotes and keypad carry over without a full re-fit.
Our technicians have up to 8 years of experience, and their training is dedicated to gates. We’ll tell you straight when a brand is repairable and when a replacement is the better spend, and you can see how a gate-only specialist approaches a job on our Enterprise page.
FAQs – Gate Motor & Opener Cost
How much does a new gate opener cost in Enterprise?
A new residential gate opener in Enterprise typically costs between $450 and $1,600 installed, depending on whether it’s a swing gate or a slide gate. Commercial slide gate operator replacements usually run $1,200 to $2,400 or more. Call (844) 423-3067 for an exact quote from a free on-site estimate.
Is it cheaper to repair or replace a gate motor?
In most cases, repairing a specific component is cheaper than replacing the operator – control board, receiver, safety sensor, or battery backup repairs typically run $120 to $650. Full operator replacement makes more sense when the motor itself has failed or the operator is past its mechanical life. A free estimate tells you which path fits your gate.
How much does a control board or receiver replacement cost?
Control board replacement in Enterprise typically runs $180 to $450, and a receiver with remote costs $120 to $350. Both are well under the cost of a full operator replacement, which is why we check them first when an operator won’t respond.
Can you come today if my gate won’t open?
Same-day service is often available, and we answer the phone 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Call (844) 423-3067 and we’ll book the soonest opening for your gate.
Do you work on my brand of gate operator?
Yes – we work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That covers most operator brands on residential and commercial gates in Enterprise, so the answer to “we don’t work on that brand” is rarely a dead end with us.
Are safety sensors and battery backups priced separately?
Yes, they’re priced as line items. A safety sensor pair typically costs $150 to $400, and a battery backup install runs $200 to $450. On a new operator installation, these are usually quoted together with the operator. The written estimate sets the final total.
Is a commercial gate motor more expensive than residential?
Yes, commercial gate operators cost more because they’re built for higher daily cycle counts and heavier gates. A commercial slide operator replacement typically runs $1,200 to $2,400 or more, versus $450 to $1,600 for a residential opener. Call (844) 423-3067 for a free estimate on a commercial motor.
Our technicians have up to 8 years of experience, and every estimate is free. Call (844) 423-3067. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Whether you need a stuck gate diagnosed, a failed operator replaced, or a full installation, a free written estimate is the fastest way to a firm price.
Pricing reflects the Enterprise market as of 2026. Gate Repair Enterprise offers free estimates – call (844) 423-3067.
Written by the team at Gate Repair Enterprise.
What Our Customers Say
"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
- Alejandro Rodriguez"Fixed the immediate problem. He was honest that the operator is near end of life and I should budget for a replacement, which I appreciate even if it wasn't what I wanted to hear."
- Travis Kowalski"The loop detector under the driveway had failed and residents were stuck holding the button. He traced it, found the break, and had the exit loop reading cars again the same visit."
- Diego Morales